MODEL MT-211232 RS-232 SWIPE READER, 1 OR 2 TRACK, BUFFERED/UNBUFFERED MODES INSTALLATION AND OPERATION MANUAL Manual Part Number 99821103 Re
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 2 FEATURES Major features of the Swipe Reader are as follows: • Hardware Compatible with AT/PS-2 PC
Section 1. Features and Specifications 3Buffered Mode In the buffered operating mode, the Reader stores the card data in a memory buffer and do
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 4 SPECIFICATIONS Table 1-1 lists the specifications for the MT211232, RS-232 Swipe Reader, 2 Track. F
Section 1. Features and Specifications 5 Figure 1-3. Dimensions
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 6
7SECTION 2. INSTALLATION The hardware installation consists of plugging in the appropriate cables for the selected configuration, setting the swit
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 8 The cables attached to the Readers have a 9-pin connector. The Pin list for this connector is provide
Section 2. Installation 9Table 2-2. Adapter Cable with Control Signals, 9-pin to 9-pin For PC: AT Connector: 9-pin to 9-pin Part N
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 10 Table 2-5. Adapter Cable without Control Signals, 9-pin to 25-pin For PC: XT PS/2 Connector: 9-
Section 2. Installation 11 Figure 2-2. Y Cable Part Number 21083534 Figure 2-3. Y Cable Part Number 21083543
ii Copyright© 1994-2005 MagTek®, Inc. Printed in the United States of America Information in this document is subject to change without notice. No
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 12 POWER ADAPTERS For standard 110 volt AC operation, the MT-211232 must be powered by the 9 volt DC a
Section 2. Installation 13Block A Switches Switches A1, A2, and A3: These switches set the baud rate, or the rate at which data is transmitted
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 14 Switch B2: This switch sets the operating mode (BUFFERED or UNBUFFERED). Switch 2 should be set to
Section 2. Installation 156. Swipe a card through the Reader. 7. If the green LED goes out momentarily, then goes ON, the Reader is working a
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 16 Data bits: 7 Parity Even Stop bits: 1 Flow Control: Hardware Clic
17SECTION 3. OPERATION Included in this section are Indicators, Card Read, Reader to Host Message Format, Host to Reader Commands, a timing diagra
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 18 READER TO HOST MESSAGE FORMAT Figure 3-1 shows the format in which data is transmitted after a card
Section 3. Operation 19 <STX> <ESC> ERROR <CR> <ETX> End of Text Character (03 He
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 20 Table 3-1. Buffer Commands I and R Switch B2 Command Description ON <ESC> “I “ Inquiry C
21APPENDIX A. PINPAD INTERFACE This appendix describes the MagTek PINPad interface to the MT-211232, 1 or 2 Track, Swipe Reader. CONNECTOR When
iiiLIMITED WARRANTY MagTek warrants that the products sold to Reseller pursuant to this Agreement will perform in accordance with MagTek’s published
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 22 • If there is no response when the PINPad button is pressed, perform the steps below. • If the Re
Appendix A. PINPad Interface 23Hyper Terminal Test Ensure the Swipe Reader and Hyper Terminal are setup as described in Section 2. Ensure th
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 24 10. The above sequence will appear similar to the following: %ABCDEFGHIJKLMNOPQRSTUVWXYZ11111111111
25APPENDIX B. TOP ASSEMBLY DRAWINGS The top assembly drawing for Track 2 and 3, Part Number 21088008, is typical of MT-211232 Swipe Reader, 1 or
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 26 Figure B-1. MT-211232 Top Assembly Drawing - Typical
Appendix B. Top Assembly Drawings Figure B-2. MT-211232 Top Assembly Drawing - Without Power Supply 27
MT-211 RS-232 Swipe Reader, 1 or 2 Tracks 28
iv FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of FCC
vTABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS--------------------------------------------------------------------- 1 FEATURES----------
vi Table 2-4. Adapter Cable without Control Signals, 9-pin to 9-pin---------------------------------------------------- 9 Table 2-5. Adapter Cable
vii
Figure 1-1. RS-232 Swipe Reader viii
1SECTION 1. FEATURES AND SPECIFICATIONS The Model MT-211232, 2-Track, RS-232 Swipe Reader, is a compact magnetic stripe card reader which conforms
Commentaires sur ces manuels